Double Row 2025 SMD LED Strip Light, DC 24V 384 LEDs/M, Warm White to Daylight Options, Self-Adhesive for Cove & Accent Lighting

Double Row 2025 SMD LED Strip Light, DC 24V 384 LEDs/M, Warm White to Daylight Options, Self-Adhesive for Cove & Accent Lighting

Single-row strips inside a wide cove leave a tell-tale signature: a bright core with visibly darker edges, because the emitting area is narrower than the channel it sits in. Widening to a double-row layout addresses this at the source. This 2025 SMD strip places 384 LEDs per metre across two parallel rows on a 10mm board, spreading the same electrical load over a wider emitting surface — the light fills a standard cove channel edge to edge instead of concentrating in a band down the centre.

Overview
Core Features
Application Scenarios
Technical Specifications
Contact

Overview

Description

Running on DC 24V rather than 12V is the second practical advantage: at 18W per metre the current draw is 0.79A, roughly half what an equivalent 12V strip would pull. Lower current means less voltage drop along the run, so single feed points can serve considerably longer continuous lengths before brightness falls off at the far end — a material difference on long cove runs and perimeter installations where a 12V strip would need intermediate power injection. Output is 2100 lumens per metre, with six colour temperatures from 2700K through 6500K specified at order stage.

Installation is tool-free via double-sided adhesive tape film. The strip cuts every 31.3mm — coarser than the single-row models in the range, which is the expected trade-off of a two-row circuit layout, so allow slightly more tolerance when planning runs against fixed end points. Rated IP20 for indoor dry-location use, with CE, CB, and RoHS certification held by the manufacturer.

Core Features

Double-row 384 LEDs/M layout — two parallel rows across a 10mm board spread the emitting area wider than a single-row strip, eliminating the dark edges that single-row strips leave in standard cove channels.
24V operation for longer runs — 0.79A per metre at 18W, roughly half the current of an equivalent 12V strip, reducing voltage drop and allowing longer continuous lengths from a single feed point.
2100 lumens per metre — significantly higher output than the 1100–1300 lm/m range of single-row 2025 models, suited to primary ambient lighting rather than accent alone.
Six colour temperature options at order — 2700K, 3000K, 3500K, 4000K, 5000K, 6500K specified when ordering; the strip is manufactured to a fixed colour temperature and is not field-switchable.
Energy efficiency class E — among the more efficient configurations in the 2025 range at this output level, despite the 18W/m draw.
Self-adhesive backing — double-sided tape film bonds directly to aluminium channels, plasterboard coves, and painted surfaces without mounting clips.
L80B20 at 20,000 hours — retains 80% of initial output at 20,000 hours with MTBF rated at the same figure.
CE / CB / RoHS certified — manufacturer-held certifications supporting European and international B2B procurement.

Application Scenarios

Cove and pelmet lighting — double-row emitting area fills standard cove channels edge to edge, removing the bright-core/dark-edge signature of single-row strips.
Long perimeter runs — 24V low-current operation supports extended continuous lengths from one feed point in hotel corridors and open-plan ceilings.
Living room and bedroom ambient lighting — 2100 lm/m provides primary ambient illumination, not just decorative accent.
Retail ceiling and perimeter accent — even wide-band output across shop-fitting channels and display perimeters.
Office and commercial ceiling features — six colour temperature options allow matching to 4000K office standards or warmer hospitality schemes.
Architectural recesses and reveals — 10mm board seats in standard channel profiles; wider light band reads as continuous from normal viewing distance.

Technical Specifications

Model No. — JNL-L-024V-2025-0384-10-S1XX
Item No. — 101300174
LED type — 2025 SMD
LED quantity — 384 PCS/m (double row)
Rated voltage — 24 V DC
Rated power — 18 W/m ± 10%
Input current — 0.79 A @ 1m
Luminous flux — 2100 lm/m
Colour temperature — 2700 / 3000 / 3500 / 4000 / 5000 / 6500 K (specified at order)
Colour rendering index — Ra 80
SDCM — ≤ 5
Beam angle — 120°
Lumen maintenance — L80B20 @ 20,000 h
Energy efficiency class — E
Ingress protection — IP20 (indoor dry location only)
Outline dimensions — W10 × H1.2 ± 0.5 mm
Surface material — Bare PCB (no silicone sleeve)
Cut length — 31.3 mm
Mounting method — Double-sided adhesive tape film
Dimming method — Turn on the power and it lights up
Switching cycles — 15,000 times
Operating temperature — -25°C to +45°C
Storage temperature — -40°C to +60°C
Relative humidity — 10–90%
MTBF — 20,000 h
Connector compatibility — 2P board connector, 2P wire connectors (single & double end), 2P board-to-board straight / L-shape / T-shape / +-shape, 2P DC-head variant
Packing — Reel + ESD bag + Inner box + Carton
Packing quantity — 5 m/roll × 100 rolls = 500 m per carton
Certification — CE / CB / RoHS

Contact

Request quotation, datasheet, or free sample reel: tel: +86 18933392222 | email: [email protected] | global.joineonlux.com — OEM, bulk order, and distributor pricing available.