Key Features

• 1000 lm/m from only 252 LEDs – The lowest die count in the 8mm D-series family still produces four-figure output per metre, giving roughly 3.97 lumens per LED against the 2.19 lm/LED of the 480-LED board.
• 10.0 W/m at 0.42 A on 24 V DC – Low current draw for the output level; a 100 W driver covers a 10 metre run with 20% headroom already allowed for.
• 8 mm × 1.65 mm profile – W8 × H1.65 ± 0.5 mm fits standard 8 mm channel internals while giving a wide, generous emitting face for even wash on cabinet undersides.
• 55.6 mm cut interval for long runs – Fewer cut points per metre means fewer solder pads interrupting the board, which suits continuous linear installations over short segmented ones.
• COB large die 6 × 20 mil, dot-free – Continuous phosphor coating across the full width eliminates visible LED points at close viewing distance, including direct sightlines under a 600 mm cabinet.
• Six colour temperatures, SDCM ≤ 5 – 2700 / 3000 / 3500 / 4000 / 5000 / 6500 K specified at order, held to a five-step MacAdam ellipse for reel-to-reel consistency.
• L80B20 at 20,000 hours with 20,000 h MTBF – Photometric and reliability figures aligned, with 15,000 rated switching cycles for door-triggered wardrobe circuits.
• Complete 2P-8 accessory ecosystem – Solderless board connectors, DC Dupont leads, in-line joiners and L, T and cross transitions cover extension, cornering and branching.

Specifications

Applications

• Wardrobe and closet rails – Long uninterrupted hanging rails suit the 55.6 mm repeat; 1000 lm/m clearly separates garment colours across a full-depth carcass.
• Kitchen cabinet undersides – Genuine task-level output onto worktops from a slim 1.65 mm profile that stays hidden behind the cabinet lip. Keep the run clear of sinks and hobs; the board is IP20 and for indoor use only.
• Indoor skirting and corridor baselines – Continuous low-level wayfinding light where run length matters more than fine length granularity.
• Bed head and under-bed lighting – Soft indirect light at 120° from a concealed 8 mm band, with 15,000 switching cycles suited to nightly use.
• Wine cabinets and bar shelving – Warm 2700K or 3000K options wash bottle rows evenly without hot spots on glass.
• TV backlighting and media walls – A single 24 V feed drives the full perimeter of a large panel with minimal end-of-run fall-off.
• Cove and perimeter ceiling detail – 120° beam and dot-free emission give a clean bounced line off plaster or plasterboard returns.

Certifications

• CE
• CB
• RoHS
• Test reports available on request

Packing & Logistics

• Packing type: reel + ESD bag + carton
• Packing quantity: 5 m per roll, 100 rolls per carton, 500 m total
• MOQ: 50 sets
• Lead time: 15–21 days
• Port of loading: Guangzhou / Shenzhen

Service

• Warranty: 2 years
• Samples: free samples on standard items; freight collect
• Response time: within 2 hours
• After-sales: technical support by email or phone throughout the warranty period. Report quality issues with photographs, video, and the item number; verified defects are resolved by replacement parts or replacement units shipped with your next order, or by credit where no follow-up order is scheduled. Faults caused by physical damage, unauthorised modification, or use outside the rated environmental conditions fall outside warranty cover.
• Contact: tel: +86 18933392222 | email: [email protected]

FAQ

Q: How can 252 LEDs produce 1000 lm/m when denser strips in the same family produce less?
A: Output per metre is a function of total power and emitter efficiency, not die count alone. This board spreads 10.0 W/m across 252 large-die 6 × 20 mil emitters, so each die runs at a higher drive current and contributes about 3.97 lumens. A 480-LED board at 12 W/m splits its power across nearly twice as many dies, each contributing less. Density affects the fineness of the emitting surface; power and efficiency determine brightness.

Q: Is the 55.6 mm cut interval a disadvantage?
A: Only if your segments are short. On a 400 mm display compartment a 55.6 mm repeat can leave up to 55 mm unlit, which is noticeable. On a 2 m or 3 m continuous run the same rounding error is irrelevant and the longer repeat means fewer cut pads along the board. Specify this model for long runs and the 480 or 512 LED versions where exact short lengths are required.

Q: Does the lower die count make the light line look patchy?
A: No. The COB format covers the whole board with one continuous phosphor layer, so what you see is a solid 8 mm band rather than individual emitters. Die spacing on a 252 LED/m board is roughly 4 mm, well inside the diffusion range of the phosphor at any normal viewing distance.

Q: Can this strip be used above a kitchen sink or hob?
A: No. The rating is IP20, which means an unsealed board with no protection against water, spray or condensation. It is for indoor use only and must be kept away from sinks, hobs, steam paths and any location where it could be wetted or wiped down with liquid. Position it under the cabinet front lip, clear of extraction plumes.

Q: What is the maximum single run from one power feed?
A: At 0.42 A per metre on 24 V DC the current builds relatively slowly along the board, so runs of several metres are practical from one feed. Exact length depends on your acceptable end-of-run drop, conductor cross-section and driver location; feeding from the centre of a long run rather than one end roughly doubles the achievable length.

Q: What are the MOQ, lead time and packing arrangements?
A: MOQ is 50 sets and lead time is 15–21 days. Product ships as 5 m reels in ESD bags, 100 reels per carton for 500 m total, from Guangzhou or Shenzhen.